TABLE OF CONTENTS
Thank You for your ERC-1 Purchase
Limited Warranty
5
6
6
7
Service Assistance For the ERC-1
Emotiva Disclosure
FCC Compliance
7
Safety Precautions
8
9
A Note for the Cable Television (CATV) Installer
Unpacking the ERC-1
9
9
Inventory
TECHNICAL SPECIFICATIONS
10
11
Key Features of Your New ERC-1 Audiophile CD Player
Disc Handling
12
12
Discs usable with the ERC-1
Holding discs
12
12
12
12
12
Loading discs
Cautions on loading discs
Cautions on handling discs
Disc Storage
FRONT PANEL LAYOUT
13
14
REAR PANEL LAYOUT
REMOTE CONTROL
15, 16
17
Changing the Remote Control Batteries
OPERATING INSTRUCTIONS
Loading and ejecting discs
Normal disc play
18
18
18
18
19
19
Locating a specific track
Locating a particular point in a track
Repeating discs and tracks
3
TROUBLESHOOTING
20
20
20
20
20
20
20
20
The disc does not rotate
The disc is playing but there is no sound
The disc stops, noise is heard or the sound drops out
A CD-R / CD-RW disc cannot be played
The remote control does not operate
A specific CD cannot be played
Digital signal has no output
4
THANK YOU FOR YOUR ERC-1 PURCHASE
Dear Music Enthusiast,
Thank you for purchasing the Emotiva ERC-1 CD Player. We sincerely believe that it offers you
outstanding performance and value. Emotiva products are engineered and produced with the
highest quality materials and incorporate the latest technology. We think you will find the
Emotiva ERC-1 meets or exceeds your expectations.
The ERC-1 is a high quality audiophile grade CD player. It has been designed for maximum
performance, ease of use and installation flexibility. The ERC-1 reproduces music the way it
was created; dynamic, crystal clear, open and engaging. The subtle pull of a bow, the thrashing
of a power chord, the gentle nuances of a vocal performance; it’s all there, waiting to be
experienced by you like never before.
The ERC-1 features a 24 bit processor with 384 x oversampling maintaining the ultimate
transparency and openness from the CD source.
Also featured:
Independent shielded power supplies for each section of the unit (CD Carriage, Digital Circuits,
Analogue Circuits, Display) ensure minimal noise and interaction between each section resulting
in a cleaner pure listening experience.
The DAC (digital to analog converter) is the Analog Devices 1955.
The Op-amps are Burr Brown OPA2134.
As per the Emotiva legacy only the finest available parts are used.
5
LIMITED WARRANTY
The Emotiva ERC-1 CD Player has been created to perform flawlessly for many years. As a
result of this quality and craftsmanship, Emotiva offers the following warranty to owners of the
ERC-1.
Emotiva Audio warrants the ERC-1 to be free from defects in materials and workmanship for a
period of five years from the original date of purchase. The following items are excluded from,
or will void this warranty coverage:
1) Damage to the ERC-1 caused during shipment and handling. (If you receive an item that
you believe to have been damaged during shipment, please contact Emotiva
immediately. Phone: 877-EMO-Tech (877-366-8324) / Email: [email protected]
2) Damage to the ERC-1 caused by accident, misuse or abusive operation contrary to the
instructions specified within this manual.
3) ERC-1 units that have had the serial numbers defaced, modified, or removed.
4) Damage to the ERC-1 resulting from a modification of, or attempted repair by any person
or company not authorized by Emotiva.
5) Any ERC-1 unit purchased from a non-authorized dealer.
6) Emotiva does not assume liability for loss of use or damage to associated or connected
equipment.
Service Assistance for the ERC-1
1) Please note that BEFORE sending your ERC-1 in for repair you MUST call Emotiva and
obtain a return merchandise authorization (RMA) number. Before contacting Emotiva to
begin the RMA process, please have as detailed a description of the problem(s) you are
experiencing and the conditions under which the problem(s) occur. Additionally, please
be sure to check the troubleshooting guide in this manual to rule out the possibility of
something simple you may have overlooked. Many instances of perceived failure are
simple operational and setup mistakes and Emotiva is happy to assist you however
possible. Please call 877-EMO-Tech (877-366-8324) / Email: [email protected]
Once you have obtained the RMA number, you must print this clearly on the outside of the box
so it will be possible to determine from whom the ERC-1 came once it arrives. Parcels arriving
without an RMA numbers will be refused and returned freight collect.
Please send your repairs with RMA to:
Emotiva Audio Corp.
Attn.: Repair Department
131 Southeast Parkway Court
Franklin, TN 37064
RMA – (Put your RMA number in this spot.)
877-EMO-Tech (877-366-8324) / Email: [email protected]
6
Emotiva Disclosure
Copyright 2009 Emotiva
All Rights Reserved. Emotiva reserves the right to make improvements to its products at any
time. Therefore, the specifications of the product and the specific details of this manual are
subject to change at any time.
Emotiva and the Emotiva "E" are registered trademarks of Emotiva Audio Corporation
NOTE: The ERC-1 is a Class 1 Laser Product
FCC Compliance:
This device complies with part 15 of FCC Rules. Operation is subject of the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
7
SAFETY PRECAUTIONS
Read this User's Guide thoroughly before attempting to install and configure the ERC-1 CD
Player. All the safety and operation instructions should be read before any operation of the
component(s) begin. After successful installation and configuration of the ERC-1 CD Player, be
sure to retain this manual in a safe place for any future reference needs.
All warnings on the ERC-1 CD Player and in these operating instructions should be followed.
Safety is a key component to a long lasting and trouble free installation. The vast majority of the
subsequent safety precautions involve simple common sense. If you are not comfortable with
the installation of audio/video entertainment equipment, it will be to your benefit to seek the
services of a qualified installation professional.
NEVER use the ERC-1 CD Player near water such as a bathtub, washbowl, kitchen sink,
laundry tub, in a wet basement or near a swimming pool etc. There is a risk of electric shock to
your body and permanent damage to the equipment. Electric shock may result in permanent
bodily injury or death.
The ERC-1 CD Player should be situated so that its location or installation position does not
interfere with proper ventilation. The ERC-1 CD Player should not be situated on a bed, sofa,
rug or similar surface that may block any ventilation openings; or placed in a built-in installation
such as a bookcase, cabinet, or closed equipment rack that may impeded the flow of air through
ventilation openings. If installed in a closed equipment rack for custom installations, be sure to
add forced air ventilation so that it has adequate air circulation. The ERC-1 CD Player should be
situated away from heat sources such as radiators, or any other devices which produce heat.
The ERC-1 CD Player should be connected to a power supply only of the type described in this
User's Guide and what is labeled on the ERC-1 CD Player component. Power supply cords
should be routed so that they are not in high foot traffic areas or pinched by item placed upon or
against them, paying particular attention to cords at the wall plugs, convenience receptacles,
and the point where they connect into the ERC-1 CD Player. The power cord for the ERC-1 CD
Player should be unplugged from the outlet when unused for a long period of time. Never spray
liquids directly into the component's vent openings. Care should be taken so that small objects
do not fall into the inside of the ERC-1 CD Player.
The following situations require that your ERC-1 CD Player be serviced only by qualified service
personnel;
1. The power-supply cord or the plug has been damaged; or
2. Objects have fallen, or liquid has spilled into the component; or
3. The ERC-1 CD Player has been exposed to rain; or
4. The ERC-1 CD Player does not appear to operate normally or exhibits a marked change
in performance; or
5. The ERC-1 CD Player has been dropped, or its enclosure or chassis is damaged.
8
A Note for the Cable Television (CATV) Installer
This reminder is to call the CATV system installer's attention to Article 82040 of the NEC that
provides guidelines for proper grounding and in particular, specifies that the cable ground shall
be connected to the grounding system of the building as close to the point of cable entry as
practical.
UNPACKING THE ERC-1
The Emotiva ERC-1 CD Player should reach you in flawless condition. If you notice any
shipping damage or other issues upon unpacking the unit, please contact Emotiva immediately.
INVENTORY
Included with your ERC-1 CD Player should be a power cord, remote control, batteries and this
User's Guide. Please take a moment to make sure all the items are there in the packaging.
Gently lift out the unit and remove all the packaging material and accessories. The ERC-1 is a
delicate instrument so please unpack it carefully to avoid unnecessary damage to the CD
player. It is important to save all the packing materials and the boxes in case your ERC-1 ever
needs to be moved or shipped back to the factory for service.
9
TECHNICAL SPECIFICATIONS
• Output voltage: 1V rms (7V peak)
• Channel separation: ≥95dB - ref. 1kHz
• Frequency response: 20Hz~20kHz (+/- 0.1dB)
• S/N: ≥100dB (A weighted）
• THD: ≤0.01％ 0dB 1KHz）
• Playback formats: Redbook CD, HDCD, MP3
• Digital Output Filter: 24-Bit, 384 times oversampling (Analog Devices 1955）
• Sampling Frequency: 44.1 kHz
• Analog output filter frequency: 80 kHz (-3dB)
• Amplitude output linearity: 0.2dB
• Phase linearity: 30°
• Power consumption: ≤ 25W
• Output connection types: digital coaxial, digital optical toslink, unbalanced RCA, balanced
XLR
• Weight: 17.5 lbs. (unboxed)
• Width: 17 inches
• Depth: 14 inches (including RCA jack extension)
• Height: 3.75 inches (faceplate only) – 4.25 inches including feet
• Feet are recessed 2.25 inches from face of unit, and .5 inches from back of unit
Analog Connections
The analog sections will use the DAC's in the player and pass an analog signal to the
pre/pro (receiver). Plug into the analog inputs of your pre/pro (receiver) to take advantage
of the processing in the ERC-1.
Digital Connections
The digital outputs (Toslink / Coaxial) will send a digital signal to your pre/pro (receiver)
allowing you to use the processing in your pre/pro (receiver).
All outputs (digital and analog) on the ERC-1 are active at all times.
10
KEY ERC-1 FEATURES
Four (4) independent power supplies to drive each section of the unit separately. This prevents
the different sections from interacting and causing noise. The separate power supplies apply to:
1. CD carriage
2. Digital section
3. Analog section
4. Display
The CD drive mechanism and the digital section of the audio is encased in a steel substructure
that shields it 100% from the audio stages. No noise from the mechanism or digital section can
get into the audio. The ERC-1 features a new, state of the art magnetic loading mechanism, and
uses high-density foam clamps, which eliminates any risk of scratching CD's when used
properly.
The audio board itself is fully isolated from the power supply and digital sections and offers a
fully discrete output stage, capable of producing 7 volts of output (no wimpy 2 volt output here!).
• Slot-load system with halo lighting.
• Lighting has two selectable functions:
o Default setting: All lights stay brightly lit constantly.
o ‘Dim’ setting: Dims the display light, and turns off the halo light and all the front
panel buttons except the On/Standby button. Halo lighting will occur when CDs
are ejected. Activate this mode by pressing the ‘Dim’ button on the ERC-1 remote.
• 12 volt trigger for automatic turn on with other sources
• Remote control
11
DISC HANDLING
Use only discs with regular shapes. If an irregular disc (a disc with a special shape) is used the
ERC-1 may be damaged.
Discs usable with the ERC-1
CD Audio (CD-DA), CD-R, CD-RW, HDCD
Holding discs
Avoid touching the surface of a disc where recording is performed.
Loading discs
Hold the CD by the edges loosely and gently slide the CD into the slot-loading
system. Wait for the ERC-1 to grab the disc, there will be a short delay while
the player grabs the disc. Release the disc into the ERC-1.
Cautions on loading discs
• Do not force the disc into the slot-loading system or it may be damaged.
• Make sure the CD label is facing up. Do not put the CD into the player upside
down or the disc may get stuck and the ERC-1 may be damaged.
Cautions on handling discs
• Do not write on the printed side with a ball-point pen or pencil
• Do not use record cleaning sprays or antistatic. Also, do not use volatile
chemicals, such as benzene or thinner.
• Do not apply labels or stickers to discs. (Do not use discs fixed with exposed tape
adhesive or leftover peeled off stickers.
• Do not use scratch-proof protectors or covers.
• Do not use discs printed with label printers available on the market.
• Do not load warped or cracked discs
Disc Storage
Be careful not to damage the disc as the data is highly susceptible to the environment
• Do not put in direct sunlight.
• Keep in a cool ventilated area.
• Store vertically
• Keep in a clean protective case.
• If you move the ERC-1 from a cold place to a warm place, condensation may
collect on the inside parts and cause abnormal disc play. If this happens, wait for
at least two hours before connecting the ERC-1 to a power outlet.
12
FRONT PANEL LAYOUT
1. PLAY/PAUSE
This is used to play and pause the disc.
2. PREVIOUS
This is used to jump to the start of the current track or to jump to the start of the previous
track.
3. NEXT
This is used to advance to the start of the next track.
4. STOP
This is used to stop the disc.
5. DISPLAY
This contains all information about the disc currently playing.
6. SLOT-LOAD SYSTEM
This is where the disc is loaded. (Blue Halo lit)
7. STANDBY
This powers the unit to on from standby and from standby to on (also performed with the
remote control). The button will glow amber when in standby and blue when on.
8. EJECT
This ejects the disc from the slot-load system.
13
REAR PANEL LAYOUT
1. BALANCED OUTPUTS (1 set)
These are used to connect the ERC-1 to a single input device (pre/pro, receiver) with
balanced (XLR) type cables.
2. ANALOG OUTPUTS (2 sets)
These are used to connect the ERC-1 to two separate input devices, (pre/pro, receiver)
with RCA type cables.
3. DIGITAL OUTPUTS
These are used to connect the ERC-1 to an input device (pre/pro, pre-amp, receiver) via
coaxial and/or optical.
SPDIF Coaxial Digital - To obtain best results, use a high quality 75 ohm digital RCA
interconnect cable (not one designed for normal audio use).
Toslink Optical Digital - Use a high quality Toslink fiber optic interconnect cable
specifically designed for audio use.
4. TRIGGER INPUT
When connected to a pre/pro or receiver with a trigger output, the ERC-1 will power up
and power down in synchronization with the connected device.
5. FUSE
6. MAIN POWER SWITCH
This rocker switch provides the master power for the ERC-1. After it is in the ON position,
the ERC-1 can be turned on manually from the front panel switch, remote control or
automatically with the trigger input via a 3.5mm input jack.
7. INPUT VOLTAGE
8. POWER RECEPTACLE
This is a standard IEC 3 prong power receptacle.
14
REMOTE CONTROL
1. EJECT
Ejects the disc from the unit.
2. DIM
This is used to dim the display light. It also turns off the
halo light and the lights for all the front panel buttons
except the On/Standby button.
3. STANDBY
Switches the unit between On and Standby mode.
4. PLAY/PAUSE
This is used to Play and Pause the disc.
5. PREV
This is used to jump to the start of the current track or to
jump to the start of the previous track.
6. REV
This is used to search backward and has three different
speeds. Press once and it moves backward, press
again faster, press a third time faster. You don't have to
hold the button down. Hit PLAY or REV again to
resume normal play.
7. FWD
This is used to search forward and has three different
speeds. Press once and it moves forward, press again
faster, press a third time faster. You don't have to hold
the button down. Hit PLAY or FWD again to resume
normal play.
8. NEXT
This is used to advance to the start of the next track.
9. NUMERIC BUTTONS (1 to 10+)
These are used to specify a desired track. Press the
number and the corresponding track will be played from the start of the track and play the
remainder of the CD.
10. REPEAT
This is used to repeat one track or all of the tracks on a disk. Press the REPEAT button once
and the display reads REPEAT ONE, press the REPEAT button again and the display reads
REPEAT ALL, press the REPEAT button again the display reads REAPEAT OFF and the ERC-
1 returns to normal play.
15
11. A-B
This allows you to loop a certain section of a track, a full
track, multiple tracks etc. Press once to start the loop,
press again where you want the loop to end. The player
will now play the section between the two loop points.
Press the A-B button again and the ERC-1 returns to
normal play.
12. DISPLAY
Pressing the display button changes the information on
the screen.
• When the ERC-1 first starts playing
a disc the display will show the time
elapsed on the current track.
• Press the DISPLAY button while
the disc is playing and the display
will change to total time left on the
current track.
• Press the DISPLAY button again
and the display will change total
time elapsed on current disc.
• Press the DISPLAY button again
and the display will change to total
remaining time on the disc currently
playing.
• Press the DISPLAY button again
and the display will revert to the
default of total time elapsed on
current track.
16
CHANGING THE REMOTE CONTROL BATTERIES
Emotiva recommends using high quality AAA batteries in the ERC-1 remote control.
To change the remote control batteries you will need a small Philips head screwdriver.
Remove the six (6) Philips head screws on the back of the remote. Make sure you use the
proper size screwdriver so you do not damage the screw heads. This should be performed on a
stable surface. Take care not to lose any of the screws. If you lose any of the screws bring one
of the remaining screws to your local hardware store, they should be able to find you an
adequate replacement.
Turn the screw counter clockwise gently so not to damage the screw heads. When all six (6)
screws are removed, remove the back panel.
Remove the old batteries and discard according to battery maker’s instructions. Insert new
batteries making sure they are installed correctly. Use diagrams in the battery slots for
reference.
Place the back panel back on the remote and reinstall the six (6) screws, turning clockwise
gently until a snug tight fit is achieved. Do not over tighten the screws as you may damage the
screw heads and/or screw holes in the back of the remote.
Your remote is now ready to use.
17
OPERATING INSTRUCTIONS
LOADING & EJECTING DISCS
1. Press the Standby/On button, make sure unit is on.
2. The display will read EMOTIVA for a few seconds at power up. LOADING will then
appear on the screen. The player will then say READY. Insert disc into the slot-loader
gently. Do not push hard. Allow the slot-loader to grab the disc from your hand;
there will be a short delay. (If the ERC-1 does not say ready at power up, a disc is
already in the player. The disc will start playing automatically. Press STOP and then
EJECT to eject the disc.
Note:
• Do not put anything except a Compact Disc into the slot loader; foreign objects may
damage the ERC-1.
• Do not force discs into the slot-loader.
• If the Compact disc is too dirty or scratched the disc may not play.
• Never load more than one disc into the player at one time.
NORMAL DISC PLAY
Switch on your pre/pro and amplifier or receiver and select the input the ERC-1 is
connected to. Make sure your volume control is turned all the way down.
1. Press the Standby/On switch
2. Insert disc into the slot-loader (Do not force the disc. Allow the slot-loader to grab the
disc from your hand.)
3. The ERC-1 will read the disc and begin to play automatically.
4. To stop the disc at any point press the Stop button. Pressing the Play/Pause button while
the disc is playing will pause the disc. When the disc is paused the display will read
PAUSE. Play can be resumed by pressing the Play/Pause button again.
LOCATING A SPECIFIC TRACK
1. Make sure that a disc is in the player
2. Pressing the Next Button on the either the ERC-1 or the remote control will forward the
CD by one track. Repeat as necessary to find the desired track.
3. Press Play and the disc will play to the end of the disc.
4. Pressing the Previous Button on either the ERC-1 or the remote control will access the
previous track.
5. Press a number on the remote control and the corresponding track will be played.
18
LOCATING A PARTICULAR POINT IN A TRACK
1. Make sure that the disc is playing the desired track.
2. Press the Left REV Button on the remote control, the CD will then rewind within the track.
Press again and the disc will rewind faster. Press a third time and the disc rewinds faster.
Press a fourth time and the disc will resume normal play or press Play to resume normal
speed. The button does not need to be held down during this function.
3. Press Right FWD Button on the remote control, the CD will then fast forward within the
track. Press again and the disc will fast forward faster. Press a third time and the disc fast
forwards faster. Press a fourth time and the disc will return to normal play or press Play to
resume normal speed. The button does not need to be held down during this function.
REPEATING DISCS AND TRACKS
1. Make sure that the disc is playing.
2. Press the Repeat Button on the remote control. REPEAT ONE will appear on the display.
This will cause the current track to repeat.
3. Press the Repeat Button again and REPEAT ALL will appear on the display. This will
cause the disc currently in the ERC-1 to repeat.
4. Press the Repeat Button a third time and REPEAT OFF will appear on the display and
the ERC-1 returns to normal play back functions.
19
TROUBLESHOOTING
• The disc does not rotate
1. Is the power cable plugged in?
2. Is the power switch on?
3. Is the disc placed upside down?
4. Is the disc dirty?
5. Is the disc scratched?
6. Is the disc warped?
• The disc is playing but there is no sound
1. Are the receiver or pre/pro and amplifier and speakers connected correctly?
2. Is the receiver or pre/pro and amplifier turned on?
3. Is the receiver or pre/pro function set to the correct input?
4. Is the volume control set at the minimum level?
• The disc stops, noise is heard or the sound drops out
1. Is the disc dirty?
2. Is the disc scratched?
3. Is the disc warped?
*In the case of a CD-R or CD-RW disc this may occur when the conditions under which
the disc in question was recorded were substandard or if the quality of the disc itself is
poor.
*This may also occur if the disc in question has the CDDA format mixed with other data.
• A CD-R / CD-RW disc cannot be played
1. Is the disc placed upside down?
2. Does the disc in question contain the properly written TOC (Table of Contents)?
3. Is the disc in question recorded in an audio (CD-DA) format?
• The remote control does not operate
1. Is the remote control sensor blocked?
2. Is the remote control sensor pointed at the remote sensor on the front of the unit?
3. Are there batteries in the remote control?
4. Have the batteries in the remote control expired?
5. Is there strong light (from a window etc.) hitting the ERC-1's remote sensor?
• A specific CD cannot be played
1. A CD with copy controls cannot be played on the ERC-1. These are special discs
that do not comply with the current CD standards. When normal CDs can be
played and the problem only occurs with discs with copy controls there is not a
problem with the ERC-1.
• Digital signal has no output
1. Are the coaxial and/or optical cables connected correctly?
2. Is the receiver or pre/pro set to the correct input?
3. Is the input set up to receive a digital signal?
20
Revised 06/2009
All contents © 2009 Emotiva Audio Corporation.
21
|